Perpendicular Spin

Emerging Memories Today: Process Equipment Requirements

Emerging Memory ParadeSomething that distinguishes the Emerging Memory report that Tom Coughlin and I recently published is the depth in which we cover in the field.  This is not measured in pages, but in the topics that we cover.  For example, this blog post, excerpted from the report, covers the changes in tooling that will be necessary to allow a standard CMOS wafer fabrication plant (a “fab”) to produce an emerging memory technology, and the impact that this is likely to have on the market for semiconductor tools.

All of the emerging memory technologies covered in the Memory Guy’s previous post share certain things in common.  One of them is that they are built between metal layers, rather than in the silicon CMOS substrate itself (with the possible exception of the hafnium oxide FRAM.)

This means that the tooling required for any of these technologies will bear a strong resemblance to that used by any of the others.  For the most part these tools will be used for deposition and etch.  The lithography requirements will be satisfied by the tools used to pattern the metal layers.

The process flow in this figure sheds some light on the steps that Continue reading

Emerging Memories Today: The Technologies: MRAM, ReRAM, PCM/XPoint, FRAM, etc.

Emerging Memory ParadeHere in the US we use an extremely odd expression.  If there are multiple varieties of an item we commonly say: “There are more of them than you can shake a stick at!”  This is a very lengthy way to say: “numerous.”  (I don’t believe that ANYONE understands how that expression became a part of our vernacular!)  Although The Memory Guy isn’t normally seen shaking a stick, I find it an apt way to describe the numerous new memory technologies that are being pioneered today.  There are certainly lots of them!

This post is intended to be very high-level technical description of today’s leading emerging memory technologies.  These are excerpts of the in-depth descriptions that can be found in our recently-released report: Emerging Memories Poised to Explode.

PCM: Also known as PRAM, Phase-Change Memory technology is based upon a material that can be either amorphous or crystalline at normal ambient temperatures.  The crystalline state has a low resistance and the amorphous state has a high resistance.  This is controlled by melting the bit cell by passing a current though it and then allowing it to cool at different rates.

In chemistry and physics, anything with a Continue reading

Emerging Memories Today: Understanding Bit Selectors

Emerging Memory ParadeThe previous post in this series (excerpted from the Objective Analysis and Coughlin Associates Emerging Memory report) explained why emerging memories are necessary.  Oddly enough, this series will explain bit selectors before defining all of the emerging memory technologies themselves.  The reason why is that the bit selector determines how small a bit cell can get, and that is a very significant component of the overall cost of the technology.  Cost, of course, is extraordinarily important because no system designer would use a component that would make a system more expensive than it absolutely needs to be!

A number of the Memory Guy’s readers may never have heard of a selector. I’ll explain it here.  It’s not complicated.

Every bit cell in a memory chip requires a selector.  This device routes the bit cell’s contents onto a bus that eventually makes its way to the chip’s pins, allowing it to be read or written.  The bit cell’s technology determines the type of selector that is appropriate: SRAMs use two transistors, DRAMs use one transistor, and flash memories combine a transistor with the Continue reading

Emerging Memories Today: Why Emerging Memories are Necessary

Emerging Memory ParadeNon-silicon memory technologies have been studied for about as long as have silicon-based technologies, but the silicon technologies have always been preferred.  Why is that, and why should anything change?

This is a question that The Memory Guy is often asked.  The answer is relatively simple.

Silicon memory technologies benefit from the fact that they have always been manufactured on process technologies that are nearly identical to those used to produce CMOS logic, and can therefore take advantage of the advancements that are jointly developed for both memory and logic processes.  In fact, before the middle 1980s, logic and memory processes were identical.  It wasn’t until then that the memory market grew large enough (over $5 billion/year) that it could support any additional process development on its own.

Even so, memory processes and logic processes are more similar than different.  This synergy between memory and logic continues to reduce the process development cost for both memories and logic.

Emerging memories depart from Continue reading

Emerging Memories Today: New Blog Series

Emerging Memory ParadeThere’s never been a more exciting time for emerging memory technologies. New memory types like PCM, MRAM, ReRAM, FRAM, and others have been waiting patiently, sometimes for decades, for an opportunity to make a sizeable markets of their own.  Today it appears that their opportunity is very near.

Some of these memory types are already being manufactured in volume, and the established niches that these chips sell into can provide good revenue.  But the market is poised to experience a very dramatic upturn as advanced logic processing nodes drive sophisticated processors and ASICs to adopt emerging persistent memory technologies.  Meanwhile Intel has started to aggressively promote its new 3D XPoint memory for use as a persistent (nonvolatile) memory layer for advanced computing.  It’s no wonder that SNIA, JEDEC, and other standards bodies, along with the Linux community and major software firms are working hard to implement the necessary standards and ecosystems to support widespread adoption of the persistent nature of these new technologies.

This post introduces a Continue reading